60ns, 52ns SPST - NO 115Ohm QUAD Analog Switches BREAK-BEFORE-MAKE DG604 16 Pins 100pA 5V 16-WFQFN
SOT-23
DG604EN-T1-E4 Datasheet
non-compliant
In-Stock: 0 items
Specifications
Name
Value
Type
Parameter
Factory Lead Time
14 Weeks
Mounting Type
Surface Mount
Package / Case
16-WFQFN
Surface Mount
YES
Number of Pins
16
Operating Temperature
-40°C~125°C TA
Packaging
Tape & Reel (TR)
Published
2013
Pbfree Code
yes
Part Status
Obsolete
Moisture Sensitivity Level (MSL)
1 (Unlimited)
Number of Terminations
16
Resistance
160Ohm
Max Power Dissipation
525mW
Technology
CMOS
Terminal Position
QUAD
Peak Reflow Temperature (Cel)
260
Number of Functions
1
Supply Voltage
5V
Time@Peak Reflow Temperature-Max (s)
40
Base Part Number
DG604
Pin Count
16
Number of Channels
1
Number of Circuits
2
Max Supply Voltage
12V
Min Supply Voltage
2.7V
Operating Supply Current
1μA
Power Dissipation
525mW
Max Supply Current
500nA
Propagation Delay
70 ns
Turn On Delay Time
108 ns
Logic Function
Multiplexer
Number of Inputs
4
Voltage - Supply, Single/Dual (±)
2.7V~12V ±2.7V~5V
Supply Type
Dual, Single
Bandwidth
290MHz
Neg Supply Voltage-Nom (Vsup)
-5V
Turn-Off Delay Time
76 ns
Max Dual Supply Voltage
5V
-3db Bandwidth
400MHz
On-State Resistance (Max)
115Ohm
Min Dual Supply Voltage
2.7V
Dual Supply Voltage
3V
Multiplexer/Demultiplexer Circuit
1:1
Off-state Isolation-Nom
72 dB
Current - Leakage (IS(off)) (Max)
100pA
Channel Capacitance (CS(off), CD(off))
2.7pF 7.3pF
On-state Resistance Match-Nom
1Ohm
Switch Circuit
SPST - NO
Switch Time (Ton, Toff) (Max)
60ns, 52ns
Charge Injection
0.7pC
Channel-to-Channel Matching (ΔRon)
1 Ω
Crosstalk
-81dB @ 10MHz
Switching
BREAK-BEFORE-MAKE
Switch-on Time-Max
90ns
Height
750μm
Length
2.6mm
Width
1.8mm
Radiation Hardening
No
RoHS Status
ROHS3 Compliant
DG604EN-T1-E4 Product Details
DG604EN-T1-E4 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-WFQFN. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~125°C TA. 16 terminations have been made so far. By its 1 channels, the electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. A key feature of the 16 series is the inclusion of this electronic part as part of its design. Circuits based on SPST - NO switching are used to construct these analog switch ics. A total of 2 circuits make up this switch device. Try searching with DG604 if you're looking for variants. Internally, this switch multiplexer has a resistance of 160Ohm. For functions related to 16 pins, please refer to the datasheets. Multiplexers should not be powered above 12V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage the electronic part should receive is 2.7V. In order to operate this switch device, it would need a current of 1μA. It may damage the digital multiplexer if the voltage is higher than 500nA. There is no problem with using dual supply voltage, but it should not exceed 5V. For dual power supplies, a voltage of at least 2.7V should be attached. Among the inputs that can be operated are the 4 inputs. It is possible to transfer data over a 290MHz-bandwidth.
DG604EN-T1-E4 Features
1 Channels Switch Circuit: SPST - NO 1μA Supply Current -3db Bandwidth: 400MHz Bandwidth: 290MHz
DG604EN-T1-E4 Applications
There are a lot of Vishay Siliconix DG604EN-T1-E4 Analog Switches & Multiplexers ICs applications.
FTTH
Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads