Welcome to Hotenda.com Online Store!

logo
userjoin
Home

LT1280ACN

LT1280ACN

LT1280ACN

Linear Technology/Analog Devices

18 TerminationsLT1280 Receivers2 Bits 2/2 Drivers/Receivers2 Functions

SOT-23

LT1280ACN Datasheet PDF

non-compliant

Technical Specifications

Parameter NameValue
TypeParameter
Mounting Type Through Hole
Package / Case 18-DIP (0.300, 7.62mm)
Surface MountNO
Operating Temperature0°C~70°C
PackagingTube
Published 1998
JESD-609 Code e0
Part StatusObsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 18
ECCN Code EAR99
Type Transceiver
Terminal Finish Tin/Lead (Sn/Pb)
Additional FeatureEXTERNAL CHARGE PUMP
HTS Code8542.39.00.01
Subcategory Line Driver or Receivers
Technology BIPOLAR
Voltage - Supply 4.5V~5.5V
Terminal Position DUAL
Peak Reflow Temperature (Cel) NOT SPECIFIED
Number of Functions 2
Supply Voltage 5V
Terminal Pitch2.54mm
Reach Compliance Code not_compliant
[email protected] Reflow Temperature-Max (s) NOT SPECIFIED
Base Part Number LT1280
Pin Count18
JESD-30 Code R-PDIP-T18
Qualification StatusNot Qualified
Power Supplies5V
Supply Current-Max 14mA
Data Rate250KBd
Output Characteristics 3-STATE
Differential OutputNO
Output Polarity INVERTED
Protocol RS232
Input Characteristics SCHMITT TRIGGER
Number of Drivers/Receivers 2/2
Driver Number of Bits 2
Receiver Number of Bits 2
Duplex Full
Receiver Hysteresis400mV
Interface Standard EIA-232
Receive Delay-Max 600 ns
Transmit Delay-Max 1300 ns
Output Low Current-Max 0.0016A
Out Swing-Min 10 V
High Level Input Current-Max 0.00002A
Height Seated (Max) 3.937mm
Width 7.62mm
RoHS StatusNon-RoHS Compliant
In-Stock:1912 items

LT1280ACN Product Details

LT1280ACN Overview


This driver chip is excellent for driving common LEDs due to its enhanced 18-DIP (0.300, 7.62mm) package.Tube package is used to mount this receiver.It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.Ideally, you should place this wide receiver on a Through Hole-type PCB or development board.Power supply for this differential driver is 4.5V~5.5V.At any one time, this electronic part can have up to 2/2 eligible receivers/drivers.IC receiver likes this one are designed for use in applications where operating temperatures are 0°C~70°C.Driver ICs with a supply voltage range of 5V can operate efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.As a standard package, this transceiver comes with a 18-pin layout that follows the market standard.Since the base part number LT1280 describes the product type, temperature, package, etc., you might get more options by searching with it.As a result of the ic receiver, the resolution of the driver was increased to 2 bits.There are typically 2 bits of resolution specified in the specifications of this receiver.It is possible to subcategoriLine Driver or Receiverse this rf transceiver module as Line Driver or Receivers.It is designed to be operated from a 5V power supply, so the module isolated transceiver will work effectively.A EXTERNAL CHARGE PUMP function is also included in this optical transceiver module, which improves stability and accuracy of signal management.Ensure that the VCC pin of the ic receiver receives sufficient but not more than 14mA of input current.

LT1280ACN Features


Tube package
18 pin count
5V power supply

LT1280ACN Applications


There are a lot of Linear Technology/Analog Devices LT1280ACN Drivers/Receivers/Transceivers applications.

  • Wired telephone
  • Desktop radio
  • Transmission stations
  • Automation systems
  • Point-to-point networking
  • Wireless interactive experience
  • Wireless network systems
  • Switches
  • Datacom networking applications
  • Wireless projection application for conferences

Get Subscriber

Enter Your Email Address, Get the Latest News